Kitchen & BathroomElectrical InstallationDone Right

Why Kitchen & Bathroom Electrics Need a Specialist

Water is an excellent conductor of electricity. In a bathroom, a fault in a non-zone-compliant fitting can send current through water, pipes, or wet surfaces — creating a lethal shock path to anyone touching them.

Kitchen appliances draw significant current. A typical electric oven pulls 13A, a hob pulls 32A, and a kettle pulls 13A. Running these from shared circuits causes chronic overloading that degrades wiring insulation over years — creating invisible fire risks.

Non-Fully certified bathroom or kitchen electrical work is a building regulation violation. If discovered during a property sale, the buyer's surveyor will flag it — potentially delaying or collapsing the sale.

Insurance companies specifically ask about electrical work in wet areas. Uncertified modifications to kitchen or bathroom electrics can void your home insurance, leaving you unprotected in the event of fire or water damage.

DIY electrical work in bathrooms is responsible for a disproportionate number of electric shock injuries in the UK. The regulations exist because the risk is real — this is not an area for amateur work.

Design

We plan the electrical layout with your fitter. Socket positions, lighting, and circuits mapped before work begins.

First Fix

Cables installed during the construction phase. Positioned for optimal access and compliance.

Second Fix

Sockets, switches, lighting, and appliance connections fitted after tiling and decoration.

Testing

Full circuit testing including RCD, insulation resistance, and earth fault loop impedance.

Certification

Electrical Installation Certificate issued. Building control notification handled.

Zone-Compliant Design

Every bathroom installation respects the strict zoning regulations. Correct IP ratings, appropriate RCD protection, and compliant equipment throughout.

Dedicated Kitchen Circuits

Each major appliance gets its own dedicated circuit — preventing overloading, reducing tripping, and extending appliance lifespan.

Coordinated Installation

We work seamlessly with your builder, plumber, or kitchen fitter. Electrical work is timed correctly to avoid delays and rework.

Underfloor Heating

We install and connect electric underfloor heating systems with programmable thermostats. Properly rated circuits and RCD protection included.

LED Lighting Design

We design and install kitchen and bathroom lighting schemes including task lighting, ambient lighting, and IP-rated downlights for wet zones.

Full Building Regulation Certification

All kitchen and bathroom electrical work is certified and building control is notified through our industry registration.

Bathroom zones are defined as: Zone 0 (inside the bath/shower tray), Zone 1 (directly above the bath/shower to 2.25m height), Zone 2 (extending 0.6m beyond Zone 1), and the area outside zones. Each zone has specific IP rating and equipment requirements.

In Zone 0, only SELV (Separated Extra Low Voltage — max 12V) equipment rated IPX7 can be installed. In Zone 1, minimum IPX4 is required with 30mA RCD protection. In Zone 2, minimum IPX4 applies. Shaver sockets conforming to BS EN 61558-2-5 are permitted in Zone 2.

Bathroom lighting must be IP-rated for its zone location. We install IP65 rated LED downlights in Zones 1 and 2, with standard fittings outside zones. Switching is typically via pull cords inside the bathroom or plate switches outside the door.

Electric shower circuits require 10.0mm² cable on a dedicated 45A or 50A MCB, depending on the shower's kilowatt rating. The circuit must include 30mA RCD protection and be properly rated for the cable run length.

Kitchen circuits typically include: a 32A dedicated cooker circuit (6.0mm² cable), a 20A dedicated hob circuit (2.5mm² or 4.0mm² depending on load), dedicated 20A circuits for dishwashers and washing machines, refrigeration on its own circuit, and a ring main for general sockets.

USB-integrated sockets are recommended for kitchen worktop areas. We install twin-USB Type A/C combination sockets that eliminate the need for charging adapters and reduce worktop clutter.

Under-cabinet LED strip lighting is wired to a dedicated lighting circuit with a dimmer switch. We use driver units that are accessible for future maintenance and position wiring to avoid heat damage from hob proximity.

Electric underfloor heating mats are connected through a dedicated circuit with an appropriate thermostat, timer, and 30mA RCD protection. Floor temperature sensors are installed to prevent overheating and reduce energy waste.

Areas We Cover